Bridge expansion joints †performance and materials

Bridge expansion joints – performance and materials 1.1 Introduction Expansion joints are used in bridges to allow movements like expansion and contraction between the bridge deck spans and abutments. These movements are caused due to temperature, soil settlements, vehicle acceleration and other reasons (Klaiber, et al., 1987 and Dagher, et al., 1993 as cited in Thippeswamy, 2002). Expansion joints are subjected to severe loading due to the direct impact of the wheels. They are a very important component of a bridge structure and if carefully designed, properly installed and reasonably maintained will give a trouble free performance for many years. Though joints are made of various materials like rubber, silicone and polymer they deteriorate since they are constantly exposed to impact, vibration of traffic and natural elements like water, dust, ultra violet rays and ozone (Chang Lee 2002). The durability of expansion joints is a major concern to bridge owners. The maintenance cost of joints is relatively high than the initial cost .This led to the de sign of jointless bridges. Jointless bridges do not develop stress due to corrosion of joints, accumulation of debris and differential elevation of joints (Thippeswamy, 2002). The behaviour of the jointless bridges not known and the designs being complicated are not implemented in spite of their advantages. This literature review deals with: characteristics of a good expansion joint that must be noted while design a joint, defects observed in expansion joints, survey studies conducted on existing joints to study their behaviour and some manufactures of bridge expansion joints in the industry. Studies on improving the performance of expansion joints is conducted, research on reducing the cost of maintenance of the joints should be conducted. 1.2 Characteristics of a good expansion joint A bridge expansion joint for proper functioning must have the ability to: accommodate movements in vertical and horizontal direction; withstand applied loads; resist skid and corrosion; operate silently with less maintenance (Lee, 1994). Price (1984) suggests that the performance of a joint is influenced by structural movements of the joint in horizontal and vertical direction, traffic loading, materials used, condition of the substrate, weather and temperature during joint installation, workmanship and performance of bearings. 1.3 Commonly observed joint defects Guzaltan (1993) as cited in (Chang Lee 2002) studied some commonly observed defects in expansion joints. They include damaged seals, accumulation of debris in the joint components, rusting of metal plates and nuts, cracking of concrete, corrosion of steel reinforcement, water leakage, improper joint alignment and joint vibration during vehicle passage. Fincher (1983) as cited in (Chang Lee 2002) presents the results of a survey conducted by Federal Highway Administration during a five year evaluation period which demonstrated that 60% of the expansion joints examined leaked. Additionally, Wallbank (1989) as cited in (Lee, 1994) explains that in a survey conducted on two hundred bridges by The London Department of Transport, the deterioration of the expansion joints was caused due to leaking and faulty drainage details. Chang and Lee (2002) conducted a study to observe the performance of joints in Indiana and found that some joints failed due to cracks in the seal and suggested test ing it before installation. Fault tree modelling was used for qualitative explanation of bridge element interaction but could be used only for catastrophic failures (Attoh- Okine Bowers 2006). These models are not applicable to bridges since they fail over an extended period of time. Fault tree models were also prepared by LeBeau and Wadia-Fascetti (2000) and Sianipar and Adams (1997) as cited in (Attoh- Okine Bowers 2006). A new deterioration modelling based on belief networks that effectively capture and illustrate the hierarchical, interaction and uncertainty factors present in bridge deterioration was developed by Attoh- Okine and Bowers (2006). Belief networks are also called Bayesian belief networks and are based on Bayes theory. The belief network approach is more appropriate than fault tree analysis since it can be used to investigate the components of a bridge including deck material, girders, bearings and abutments have a great influence on deterioration. 1.4 Studies conducted on the performance of existing expansion joints Chang and Lee (2002) conducted a study to observe the performance of the different joints used in the highway bridges in Indiana. Five popularly used joints were: compression seal (B.S), strip seal (S.S), integral abutment (I.A), poured silicone (X.J.S) and polymer modified asphalt (P.M.A). The data was obtained from questionnaire survey, analysis of Indiana Department of Transportation (INDOT) roadway management data and expert interviews. Questionnaire survey was conducted by giving questionnaires to the state bridge inspectors and engineers around Indiana. The problems with joints were encountered and possible improvements were suggested. The analysis of historical data using logistic regression approach found that S.S joint had the best performance. The expert interviews consider I.A joint to offer good results and suggest improvement of B.S and S.S joints. An inspection campaign was conducted on 150 expansion joints of 71 road bridges in Brisa, Portugal where the maintenance cos t reached a peak of 25% (Lima Brito 2009). The joints installed within the traffic lane of the bridge were considered. The expansion joints were characterised based on their type, and age of the bridge. It was recorded that the joints used more frequently included reinforced elastomeric cushion joints, elastomeric flexible strips, and asphaltic plug joints. The data obtained from the inspection campaign was statistically analysed. The results showed that joints that were replaced mostly frequently were elastomeric joints and that different joints have specific maintenance needs. The transition strip and the anchorage cavities of the expansion joint are the parts that require more maintenance. It was also observed that the errors during installation and lack of maintenance caused pathology of the joint. The results of campaign conducted show that there was a lot of improvement in the commercial expansion joints and suggests investigation on the new or improved systems and materials. It also suggested that simple systems with fewer components are more reliable and require less maintenance. Asphalt bridge expansion joints when used in cold countries cracked within the first two years. To improve the performance the commercial MEIJIA asphalt binder was modified with polymers: thermoplastic rubber and rubber (Yu, et al., 2009). The polymers were used in various combinations, and their performance at low temperatures is evaluated by conducting tests including: ductility, penetration, indirect tension and bending tests. The data from ductility and penetration tests performed on binders indicated that the strength and deformation capacity at low temperatures improved. Four expansion joints made with the modified asphalt mixtures were installed on two bridges in a cold region and found that the joints showed good performance. 1.5 Assessment of expansion joint performance using monitored data A study was conducted by to develop a procedure for verification of the design and evaluating the condition of expansion joint by monitoring joint displacement and bridge temperature on a long term (Ni, et al., 2002). This method was applied to Ting Kau, cable stayed bridge in Hong Kong. The service life and replacement of joint depends on the cumulative displacement. An accurate prediction of the cumulative displacement will provide the time interval for joint inspection or joint replacement. Monitoring the thermal movements at the expansion joints and comparing them with the design values provide verification on design. The whole system had more than 230 sensors like anemometers, accelerometers, displacements transducters to measure displacements located at the ends of the deck, temperature sensors, strain gauges, weight in motion sensors and global positioning system. A good correlation between the movement of the expansion joints and effective temperature was observed. The daily average cumulative displacements of the expansion joints in the bridge are much less than design values. Additionally monitoring systems had been implemented on many bridges in different countries by (Andersen Pedersen 1994; Cheung et al. 1997; Barrish et al. 2000; Sumitro et al. 2001; Mufti 2002; Koh et al. 2003; Wong 2004) as cited in (Ni et al. 2002). 1.6 Effect of SSI and ground motion spatial variation Chouw and Hao (2008(a)) studied the effects of soil-structure interaction (SSI) and ground motion spatial variation effect on bridge pounding responses for bridges with a traditional expansion joint between adjacent girders. The study was conducted on two adjacent bridge frames. It was confirmed that structures that are built on stiff soils may experience larger pounding forces than those on soft soils. It was also examined that decrease of ground motion correlation caused larger pounding responses. Numerical simulation was conducted by nonlinear dynamic response analysis and investigated pounding mitigation and prevention of unseating in the highway bridges due to seismic forces (Raheem, 2009). It was observed that seismic pounding generates significantly higher magnitude and short duration acceleration pulses than typically assumed design magnitude. This results in severe impact forces that damage structural members like the deck or pier. Additionally the effects of SSI and bridge pounding response for bridges with modular expansion joint system (MEJS) were observed (Chouw Hao 2008(b)). It was concluded that the girders with a large gap of a MEJS caused stronger impact forces. It was found that significance of nonuniform ground motions depends on the properties of the ground motions, subsoil and the structures. 1.7 Types of Expansion Joints 1.7.1 Selection of joint type The type of joint is selected depending on the movement expected for serviceability limit state. More than one type of joint may be suitable for a particular range of movement. The movement range that should not be exceeded for each expansion joint is given in Table 1. Table 1. Selection of joint type (Department of Transport, 1989) Joint Type Total acceptable longitudinal movement Maximum acceptable vertical movement (mm) Maximum (mm) Minimum(mm) Buried Joint under continuous surfacing 5 20 1.3 Asphaltic plug joint 5 40 3 Nosing joint with poured sealant 5 12 3 Nosing with preformed compression seal 5 40 3 Reinforced Elastomeric 5 * 3 Elastomeric in metal runners 5 * 3 Cantilever comb or tooth joint 25 * 3 * Maximum value varies according to manufacturer or joint type 1.7.2 Modular bridge expansion joint Modular expansion joint is used when the joint movement exceeds 100mm.The modular expansion joint has many advantages including: water-tightness, corrosion protection, great potential as they increase the life of concrete and steel bridges (Crocetti Edlund 2003), greater movements in translation and rotation. It can accommodate the three dimensional movements without generating additional stresses or strains in the load-bearing members or in adjacent bridge or abutment structures. 1.7.2.1 Noise generation in a modular expansion joint The traffic generates more noise on bridges than on roads, as sound is produced on the top and bottom of the deck. The noise generated from a modular expansion joint under vehicle passage is louder than those of ordinary expansion joints (Ravshanovich, et al., 2007). The mechanism of noise generation for a modular bridge expansion joint which causes noise pollution was studied by conducting tests on a full scale model of a joint. A series of car-running experiments were conducted on the joint and studied its noise and vibration characteristics. A modal analysis of the joint is performed using finite element modelling. It was observed that the frequency of the noise generated above the joint varies from 500 to 800Hz due to sudden change in air pressure within the gap formed by rubber sealing with the middle beams. The frequency is less than 200Hz below the joint caused by the sound radiation due to the bending vibration modes of the middle beams being excited by an impact force from t he car wheels. Likewise a numerical investigation was conducted on a modular expansion joint of an expressway bridge to understand the generation and radiation mechanism (Ghimire, et al., 2009). The numerical analysis was conducted using finite element method. 1.7.2.2 Performance of Modular expansion joint Modular joints have the ability to cope with large thermal expansion and contraction of large bridges (Chouw Hao 2008(b)). They are capable of preventing girder pounding during strong earthquakes. A complex joint was modelled to study the dynamic response of a modular bridge expansion joint (Crocetti and Edmund, 2003). The vertical loads perpendicular to the roadway plane were considered. Horizontal loads were eliminated since the excitation mechanism was sophisticated and the behaviour of the joint in the horizontal direction was stochastic in character. A single fatigue test was performed. Data from the field tests including measurement of wheel load distribution factors, horizontal and vertical wheel loads, determination of damping and natural frequencies were obtained from Lehigh University, Bethlehem, Pennsylvania. The result of the fatigue test conducted agreed with the S-N curve plotted for welded connection between the support bar and the centre beam suggested by Dexter, et al. (1997) cited in (Crocetti Edmund 2003). Additionally an experimental investigation was performed to study the fatigue performance of a welded multiple support bar modular bridge expansion joint (Chaallal, 2006). The welded multiple support bar modular bridge expansion joint was used in the rehabilitation of Jacques Cartier Bridge in Montreal. The vertical and horizontal loads were considered unlike (Crocetti Edmund 2003) which is more practical since the expansion joints are subjected to both vertical and horizontal loads. Experimental tests were conducted on three subassemblies of the modular joint for various loads and S-N curve was plotted. 1.8 Manufacturers of Expansion joints 1.8.1 The Bridge Joint Association Bridge Joint Association (BJA) prepares standards and current practice sheets. It comprises of manufacturers and installers of bridge expansion joints which include: ASL CONTRACTS LTD, FREYSSINET LTD, GRACE CONSTRUCTION PRODUCTS LTD, Highways Maintenance Specialists LTD and MAURER LTD (Bridge Joint Association, 2009). 1.8.2 Watson Bowman Acme Corporation Watson Bowman Acme Corporation (WBA) found in 1950 isa recognized innovator in the development and manufacture of expansion joint controlsystems. Some of the joints manufactured by WBA include: Wabo ®Crete SiliconeSeal This is a high performance expansion joint system that uti ­lizes a two-part sealant between elastomeric concrete headers made of Wabo ®Crete II capable of absorbing impact loads. The headers are coupled with Wabo ®SiliconeSeal make it an ideal expansion joint system that is adopted in the industry for new construction or repair of existing joints. Wabo ®Crete II elastomeric concrete is widely used in header applications for bridges and parking structures. Polyurethane is used in the header material to minimize edge spalling associated with high impact loads while achieving superior bonding capabilities. The Wabo ®SiliconeSeal is a cold applied self levelling sealant requires no priming which simplifies acceler ­ates the installation process. Wabo ®Crete SiliconeSeal system is licensed under US Patent No 5.190.395. This joint is adopted for applications with a maximum movement range of +100% / -50% of the joint gap (Watson Bowman Acme, 2007) . Wabo ®Crete FlexFoam This is an armorless expansion joint system that is designed with closed-cell foam joint seal installed with epoxy adhesive between an impact absorbing elastomeric concrete header. The high impact absorbing, ambient cured and self-levelling properties of the Wabo ®Crete II joint header allows for the joint system to mono ­lithically bond to the deck creating a watertight system. Using an elastomeric concrete joint header achieving superior bonding ca ­pabilities and minimizing edge spalling (Watson Bowman Acme, 2007). Wabo ®Expandex This is a flexible asphaltic plug joint system designed to accommodate minimum structure movement while providing a smooth transition between the ap ­proach pavement and the bridge deck. Wabo ®Expandex is used typically at abut ­ments or asphalt overlays due to its unique asphalt compatibility. The system combines the use of a traffic bearing plate with special aggregate reinforced modified elastomeric material (Watson Bowman Acme, 2007). Jeene ® This joint system comprises of a neoprene profile, which is air-pressurized and bonded in place with a specially formulated epoxy ad ­hesive. With properly installation, the Jeene ® joint system will not tear away, protrude out of, or slip from its original position on exposure to repeated mechanical or thermal movements. Complete adhesion of the epoxy to the profile and joint wall is achieved due to the air inflation during installation. Jeene ® is the most durable, versatile, cost-effective and watertight expansion joint (Watson Bowman Acme, 2007). Wabo ®HSeal This is a pre-compressed elastomeric coated expansion joint system de ­signed to provide a permanent weather tight seal. The system is sealed in place with an epoxy, which allows it to accommodate horizontal, vertical, and skew expansion joint movements. Wabo ®HSeal consists of a micro-cell, stable to UV, polyurethane foam impregnated with a hydrophobic polymer and topped with a traffic grade elastomeric coating. The im ­pregnated foam provides a valuable secondary water tight seal in case the primary elastomeric coating is damaged. This system is supplied in pre-compressed sticks for easy installation (Watson Bowman Acme, 2007). Wabo ®Flex This is a molded rubber cushion expansion joint which is designed to accommodate structure movements from 2 inches up to 13 inches. In Wabo ®Flex system the molded rubber cushions are steel reinforced and imbedded with corrosion-resistant aluminium wear plates. Tongue and grooves at the end of each rubber cush ­ion ensure a watertight connection and prevent uplift or separation (Watson Bowman Acme, 2007). Wabo ®TransFlex This is an original reinforced elastomeric molded rubber expansion joint system. All sections feature tongue and groove fittings for tight end-to-end mating across decks and at curbs and are steel reinforced. It can be installed in new decks, or in older structures on rehabilitation projects. These joint systems readily adapt to skew angles. Wabo ®TransFlex system will accommodate anticipated thermal movements reject debris and create a level, smooth-riding, wear-resistant surface if properly installed (Watson Bowman Acme, 2007). Wabo ®Seismic WeatherSeal This is a pre-compressed elastomeric coated ex ­pansion joint system that works under its own constant internal pressure to provide a weather resistant seal. The system contains an open-cell foam seal im ­pregnated with a hydrophobic polymer sealing compound. Wabo ®Seismic WeatherSeal can be used on applications which cause simple thermal movements or on applications where seismic movement is anticipated. The Wabo ®Seismic WeatherSeal system is recommended for use on all in ­terior and exterior wall, ceiling and soffit expansion joint applications (Watson Bowman Acme, 2007). The joint systems manufactured by Watson Bowman Acme Corporation are compared as shown in Table 2, with respect to their features and their recommended area of implementation. Table 2: Comparison between the various joints manufactured by WBA. Joint Features Recommended for Wabo ®Crete SiliconeSeal Watertight system, rapid installation, Cold applied, Expansion joint applications with a maximum movement range of +100% / -50% of the joint gap Horizontal expansion joint applications on bridges and highways. Wabo ®Crete FlexFoam Accommodates movement cycle through compression and tension, Minimizes dirt or debris accumulation Horizontal expansion joint applications on bridges and interstate highways. Wabo ®Expandex. Provides smooth riding surface, can be milled or planed during resurfacing operations, joint openings with movements up to +/- 0.75 at time of installation Sealing joints on secondary highway bridge structures. Joint Features Recommended for Jeene ® . Accommodates forces associated with multi-directional movements, resists hydrostatic pressure, Accommodates thermal movement Sealing joints on bridges roadways and tunnels. Wabo ®HSeal Can accommodate horizontal, vertical and skew expansion joint movements, easy installation Sealing joints on bridges, sound wall barriers Wabo ®Flex maximum friction, prevents debris accumulation, reduces deflection under traffic load ­ing, maximum movement of 13 inches Bridge decks and ramps, Low height joint sealing restrictions Wabo ®TransFlex Watertight connection, prevent uplift or separation maximum movement of 13 inches Low height joint sealing restrictions bridges, decks and ramps Wabo ®Seismic WeatherSeal seismic movement capability, weather resistant, self-expanding non-laminated construction, accommodates movement up to +/- 50% Stadiums, parking garages, Replacing failed joints 1.8.3 Universal Sealants Limited Universal Sealants limited (USL) focuses on construction of bridges, tunnels, rail and other major structures. It manufactures supplies and installs specialist construction products including: bridge expansion joints; membranes for bridge deck waterproofing; protective coatings; concrete repair and car park refurbishment work. Some expansion joints offered by USL include: Uniflex expansion joints This system uses a butyl rubber membrane, bonded to the concrete and asphalt surfaces with Uniflex epoxy adhesive to provide an efficient and permanent joint that is easily installed. The system accommodates a variety of conditions from those experienced on an asphalt-covered traffic-free roof, to bridge decks with sheet membrane, spray on coating or asphalt waterproofing, also it can be used with two layer mastic asphalt or brick paving systems. The Uniflex system is chemically inert and completely impervious to water and water vapour. In buried joints the membrane is completely protected by the wearing surface. Uniflex membrane will not deteriorate during its service and the combination of a simple design and proven components makes the system naturally long-lasting and well up to the requirements of modern building and civil engineering practice (Universal Sealants UK Ltd, 2009). Febajoint This joint is fully registered with the Highways Agency, Scottish Executive and Welsh Assembley (BD 33/94: Joint Type 2) suitable for all class roads and motorways. The joint is nominally 500mm wide and not less than 100mm deep which will provide optimum movement capacity of +/- 20mm. The materials are applied hot and in a fluid condition, with temperatures up to 180 °C. Careful considerations should be made by the engineer before using this joint. Binder compounds use thermoplastic materials which contain polymer modified bitumen, mineral fillers and chemical additives (Universal Sealants UK Ltd, 2009). FEBA HM expansion joints The system is fully registered with the UK Highways Agency for type 2 application. It is a high modulus flexible, waterproof asphaltic plug joint. The main feature of this system includes a resistance to wheel tracking. This joint is suitable for a maximum horizontal design movement of  ±20mm. The FEBA HM system should be considered in places of high traffic volumes, constant standing traffic or heavy loading. The materials are applied hot and in fluid condition, with temperatures up to 180 °C. Binder compounds are classified as thermoplastic materials and contain polymer modified bitumen, mineral fillers and chemical additives (Universal Sealants UK Ltd, 2009). Nosing Joint (NJ) system This joint system is an ideal for maintenance situations and has been developed to provide a whole life economic solution for applications where asphalt plug joints are unsuitable and is registered with the UK Highways Agency, The Scottish Executive and Welsh Assembly. A surface mounted nosing joint with an elastomeric insert bonded to the rapid curing elastomeric compound known as Britflex ® Resin Mortar (Universal Sealants UK Ltd, 2009). The Transflex, Waboflex and Euroflex These joints are registered with the UK Highways Agency, the Scottish Executive and the Welsh Assembly for use on highway bridge decks (BD 33/94: Joint Type 5). These joints are reinforced elastomeric comprising of steel angles and a steel bridging plate system encased in a flexible elastomer. The movements that can be accommodated vary from 38mm to 330mm in structures including: All types of highway structures, car park decks, footbridges and podium decks (Universal Sealants UK Ltd, 2009). The Britflex ® BEJ Expansion Joint These joints are registered with the UK Highways Agency, Scottish Executive and Welsh Assembley for use on bridge decks on all classes of roads and motorways. (Department of Transport BD33/94: Joint Type 6). This system is ideal for maintenance projects where there is a need to replace failed systems. The major benefit of this system is its speed of assembly on-site (Universal Sealants UK Ltd, 2009). Londitudinal Joint (LJ) system This system has been developed to provide an effective method of sealing longitudinal expansion gaps and soffits. This joint accommodates both longitudinal and vertical movement and also provides a substantially watertight seal. The LJ joint system can be used as a waterproof cover joint or as a drainage channel under joint with the facility to install drainage outlets into the system (Universal Sealants UK Ltd, 2009). Table 3: Comparison between the various joints manufactured by USL. Joint Type Features Uniflex Expansion Joints Type 1-Buried joint under continuous surfacing Impervious to water and water vapour, long-lasting, simple design Joint Type Features Febajoints Type 2-Asphaltic Plug joint Provides optimum movement capacity of +/- 20mm, joint for use on highway bridges FEBA HM Expansion Joints Type 2-High Modulus Asphaltic Plug joint Can accommodate impact loads, maximum horizontal design movement of  ±20mm Nosing Joint system Type 4-Nosing with preformed compression seal Rapid Installation, No drilling of deck, can only be used in the situation where the gap at carriageway level does not exceed 65mm. Transflex, Waboflex and Euroflex Expansion Joints Type 5-Reinforced Elastomeric Accommodating movement from 38mm to 330mm. used for car park decks, footbridges, podium deck. Britflex ® BEJ Expansion Joints Type 6-Elastomeric in metal runners Rapid on site assembly, less future maintenance costs, easy to install Longitudinal Joints Longitudinal Joint System can accommodate both longitudinal and vertical movement, rapid installation, low maintenance, cost effective , watertight seal 1.8.4 Stirling Lloyd Stirling Lloyd specialise in the development, manufacture and application of high-performance waterproofing and structural protection membranes and systems. They deal with road and rail bridge decks and tunnels, to commercial building developments, car parks and highway maintenance solutions. Some of the joints manufactured by Stirling Lloyd include: Sentinel ® B This joint consists of a PVC flashing strip designed for various movement ranges. The flashing is bonded across the expansion gap and incorporated into the Eliminator ® water proofing system to form a continous waterproofing detail below

Behavior and thinking Essay

Humans are conditioned to act according to stimulus that are present in their environment. Thus was the belief or Russian scientist/physiologist Ivan Petrovich Pavlov (1849-1936) (Encarta, 2008). Though noted also for his work in the field of physiology, he is more remembered for the conduct of experiments for the demonstration of conditioned and the opposite unconditioned reflexes, first done on dogs in 1889 (Encarta, 2008). Pavlov’s discovery of the â€Å"conditoned reflex† was of great importance to the field og biology, since it showed a physiological foundation for the development of creatures of diverse reactions, or, behaviors, in order for the organism to be able to adapt to their surroundings (Bluden, 2001). Many researchers have tried to know the link between the physical and the mental bridge (cited in Biology and Medicine, 2008). The intersection of how the mind thinks and the behaviors that will emanate from the person is addressed in the field of biopsychology,i. e. a scientific undertaking to determine the biological basis of a person’s behavior and his thought processes (Encarta, 2008). Accroding to Catherine Harris, in her position paper, â€Å"What is the most important psychological finding of the century? †, she states that one’s biological tendencies tend to play a good part in an individual’s mental disorders (Harris, 1999). In her paper, centuries of human evolution have created an indominatable â€Å"information processing system†, one that does not take failure lightly (Harris, 1999). Anti social behaviors evolve under the most extreme adaptive pressures to adapt to one’s environment (Harris, 1999). These are forms of â€Å"cheat† behaviors to allow people to adapt. For example, â€Å"obsessive-compulsive behaviors† may be a reaction to the society’s rules and rituals imposed on an individual (Harris, 1999). Crowding is another social behavior one is prone to adapt to often (Southwick, 2008). In his observations, overcrowding tend to display the breakdown of normal behaviors, an upswing in aggression and violence, among others (Soutwick, 2008). The mind and the body does act in unison, but the final link of that act still has to be known with furhetr studies and research.

The Mountaintop by Katori Hall

Great theater can emerge from a simple yet evocative question: What if? Katori Hall, winner of the Blackburn Prize for outstanding women playwrights, asks the question: What did Martin Luther King Jr. do the night before he died? Who did he talk to? What did he say? Her play attempts to answer these questions, albeit in an imaginative rather than realistic way. The Mountaintop took home Englands Olivier Award for best play. In fall 2011, the plays poignant message resonated on Broadway, starring featuring Samuel L. Jackson and Angela Bassett. About the Playwright Born in 1981, Katori Hall is a young, vibrant new voice in modern theater. Much of her work derives from her experiences in her hometown of Memphis, Tennessee. According to her official website, her major works include: Hoodoo Love (Cherry Lane Theatre)Remembrance (Womens Project)Saturday Night/Sunday MorningWHADDABLOODCLOT!!!The Hope WellOur Lady of KibehoPussy Valley Her most recent work (as of 2012) is Hurt Village; set in a housing project in Memphis it depicts a returning Iraq veterans struggle to find a position in his disintegrating community, along with a place in his daughters wounded heart. (The Signature Theatre). However, Halls most renowned work to date is the historical/spiritual drama, The Mountaintop. The Plot The Mountaintop is a two-person drama about the last day of the Reverend Dr. Martin Luther King, Jr. The entire play is set in the Lorraine hotel room, the evening before his assassination. King is alone, trying to create yet another powerful speech. When he orders a cup of coffee from room service, a mysterious woman arrives, bringing much more than a late-night beverage. What follows is a reflective, often funny, often touching conversation in which Dr. King examines his achievements, his failures, and his unfinished dreams. Other Plays About Martin Luther King, Jr This is not the first time that a speculative drama has explored Dr. Kings amazing legacy. The Meeting, by Jeff Stetson, explores the contrasting methods and the common dreams of two dignified civil rights leaders (Malcolm X and Dr. King) who sacrificed their lives fighting for justice. Theme Analysis of The Mountaintop: SPOILER ALERT: Its not easy to analyze the messages of this play without revealing surprise elements of The Mountaintop. So, reader beware, I am about to ruin the big surprise in the play. The mysterious woman who seems to be a hotel maid is named Camae (short for Carrie May -- which might be code for carry me). At first, she seems to be a perfectly normal (beautiful, outspoken) maid, who is in favor of social change, but not necessarily in favor of all of Dr. Kings methods. As a storytelling device, Camae allows the audience to witness a more personal and irreverent side of Dr. King, one that the cameras and public appearances rarely captured. Camae is also willing to debate with the reverend on social matters, strongly and eloquently expressing her own views on racism, poverty, and the slowly progressing civil rights movement. It soon becomes clear, however, that Camae is not what she appears. She is not a maid. She is an angel, a recently created angel, in fact. Her first assignment is to inform Martin Luther King, Jr. that he is going to die very soon. Here the play shifts its focus. What begins as a behind-the-scenes look at one of Americas greatest leaders (in all his frustration and frailty), ultimately becomes a struggle to accept ones mortality and prepare for a journey into what Hamlet calls the undiscovered country. As one might expect, King isnt happy to find out that he is going to die. In some ways, his dialogue is reminiscent to Everyman, the morality play from 15th century Europe. The key difference, however, is that Everyman represents an average person who has failed to live a saintly life. Dr. King doesnt profess to be a saint (in fact, both the angel and King mention his extra-marital affairs), but he does rightly argue that he has been fighting a just cause and that he is the best person to continue the struggle for equality. During the last half of the play, King experiences the different stages of coping with death: denial, anger, bargaining, depression, acceptance. Arguably the best part of these stages is the bargaining portion when Dr. King actually gets to talk to God over the telephone. If The Mountaintop sounds morbid, theres actually a lot of humor and whimsy throughout this play. Camae is a feisty and foul-mouthed angel, and she is proud to announce that her wings are her breasts and that God is a woman. The play concludes with not only acceptance but joy and celebration for what has been accomplished, as well as a firm reminder of the dreams that have yet to come to fruition.

Singapore Airlines An Organizations Vision, Culture,...

This thread will examine and discuss Singapore Airlines’ (SIA) will be four-fold. The first section will discuss SIA’s eight ingredients of success - in light the organization’s vision, culture, and value of customer service, which have made SIA into an organization of global renowned and continuous change. After the eight elements have been dissected and investigated, the excesses aggression to vulnerabilities will be addressed. The second section will also provide examples and rationales of the difficulties SIA faces in maintaining both its leadership and culture continual improves. The forth section will discuss practices and principles which will enable other world class organizations to implement improvement and continuous change processes. SIA Ingredients of Success In today’s competitive environment Singapore Airlines (SIA) has consistently displayed excellence within the ever-changing field of service aviation. SIA’s success can be attributed to their eight principles or ingredients, which have served as evolutionary catalysts of continuous change within the organization (Jick, Peiperl, 2011). The eight elements address differing sections and aspects of organizational life, but all of the elements have one common theme - they promote the creation and cultivation of innovation by constantly seeking a new level and higher standard of organizational and individual performance (2011). The first major ingredient of success is the organization’s â€Å"policy for steadyShow MoreRelatedAsian Cultures And American Cultures Essay2452 Words   |  10 PagesCulture: Earth is bigger than what most people think; it consists of 7 continents, 7 seas, and 196 different countries. Taking that into consideration, our earth currently is supporting over 7 billion people worldwide. That is 7 billion people who are different and individuals who share different thoughts, ideas, backgrounds, and cultures. Cultures are very unique as they are different from country to country. Some adopt cultures that society accept as the norm, while others adopt different typesRead MoreAsian Cultures And American Cultures Essay2460 Words   |  10 Pagesbackgrounds, and cultures. Cultures are very unique as they are different from country to country. Some adopt cultures that society accepts as the norm, while others adopt different types of cultures; cultures that not many people, especially those outside of the country, can see eye to eye and would sometimes find them rather ‘extreme’. When comparing Asian cultures and American cultures side by side, we can easily identify the many differences between the two. For one, Asian cultures are less openRead MoreManagement and Leadership Paper1591 Words   |  7 PagesManagement and Leadership Paper Charles Lee University of Phoenix United Airlines presently manages nearly 3,000 flights daily on United, and United Express. This includes more than 200 domestic and international flights from Los Angeles, San Francisco, Washington D.C., Chicago, and Denver. United is recognized as one of the largest international airlines in the United States, enjoying global air rights in the Asia-Pacific area, in Europe, and in Latin America (United Air Lines, 2009). United’sRead MoreHrm in Aviation10615 Words   |  43 Pages Concordia University, Canada Abstract The civil aviation is an extremely competitive, safety-sensitive, high technology service industry. People, employees and customers, not products and machines per se, must be the arena of an organization’s core competence. The implications are vast and pervasive affecting no less than the organization’s structure, strategy, culture, and numerous operational activities. Human resource management (HRM), the management of people within the internal environmentRead MoreMarketing and Qantas2726 Words   |  11 PagesQueensland in 1920, being the second oldest airlines of the world. Today, the airways provide flight services across a network of 182 destinations in 44 countries covering all over the world with approximately 35,700 employees with 93 per cent of them based within Australia. The Qantas group also offers subsidiary businesses such as budget airlines, Jetstar, and other businesses in specialist services: Qantas Catering and Qantas Holidays (Qantas, 2010). â€Å"Our vision is to be one of Australia’s great businessesRead MoreChange Management in British Airways Essays2860 Words   |  12 PagesINTRODUCTION British Airways is one of the fastest growing airlines in the world. It has grown by its own leadership qualities and unique culture. Bob Ayling, Chief Executive implemented changes in the organization without getting support from its employees. He thought a change is necessary, even when BA was making record profit, because in the long run some decision has to be made. On one side he tried to raise staff morale by reinventing training programmes and by building a hotel at HeathrowRead MoreManagement Leadership Paper - United Airlines1954 Words   |  8 PagesManagement and Leadership Paper United Airlines United Airlines currently operates nearly 3,000 flights per day on United, as well as United Express. This amounts to more than 200 domestic and international destinations from hubs in Los Angeles, Washington D.C., Chicago, San Francisco, and Denver. United is known as one of the largest international airlines that is based in the United States, with global air rights in the Asia-Pacific area, in Europe, and in Latin America. (United Air LinesRead MoreAirasia Analysis4375 Words   |  18 Pagesevaluate the organization’s responses †¢ In relation to technological change, analyze how it influences policies and decision making, critically evaluate the effectiveness of the organization and recommend areas for improvement in response for the organization. The company has been analyzed using the aforementioned procedures and tools; and conclusions and recommendations have been reached from these tools. 3. Background to AirAsia 3.1. Organization Definition A ‘no-frills’ airline is defined asRead MoreAirasia Analysis4362 Words   |  18 Pagesand evaluate the organization’s responses †¢ In relation to technological change, analyze how it influences policies and decision making, critically evaluate the effectiveness of the organization and recommend areas for improvement in response for the organization. The company has been analyzed using the aforementioned procedures and tools; and conclusions and recommendations have been reached from these tools. 3. Background to AirAsia 3.1. Organization Definition A ‘no-frills’ airline is defined asRead MoreQantas Market Analysis2589 Words   |  11 PagesTable of Contents Introduction: Error! Bookmark not defined. Background 2 Business description Error! Bookmark not defined. Vision 2 Swot Analysis........................................................................................................................... Strength.......................................................................................................................... Weakness..........................................................